Compact, handy and visually pleasing 8 channel computer system with inbuilt 2.4 GHz FASST technology.

Fully equipped 8-channel computer system of superior quality, with 2.4 GHz FASST technology. The FASST system is a Spread Spectrum system with Frequency Hopping (FHSS). Das FASST System ist ein Spread Spectrum System mit Frequenz Hopping (FHSS). For this reason, it is permitted to transmit a maximum power of 100 mW EIRP, giving it ample reserves even for large-scale model aircraft and jets.

• No same channel interference, virtually no interferenc possible, not sensitive to electronic smog.
• The central point is the high-resolution 128 x 64 dot graphical display which is backlit to ensure it is easy to read.
• The elegant and clean design of the unit is made possible by the new Cap-Touch-System. Contact-free sensors for the 3D hotkey allow a smooth and sealed surface without any controls protruding.
• Simple programming using the graphical user interface, the proven menu structure and user interface was mainly adopted from the FX30/FX40 systems.
• the software is available in 8 languages:: German, English, French, Italian, Spanish, Czech, Russian or Dutch.
• Special precision dual-axis joysticks with digital trimming and trim value storage.. One of the main points of focus was an accurate feeling of control when the sticks pass through the centre position. Experience the new feeling of control for yourself..
• The controls attached to the sides make it easy to use supplementary functions without letting go of the joystick.
• The system has a total of 10 channels(8 proportional and 2 control channels), with your choice of channel sequence.
• The transmitter comes fully equipped with 4 analogue rotary knobs and 8 switches and does not require any additional equipment. For almost all functions the switches or other controls can be assigned as wanted.
• Comprehensive software provides all the essential facilities even for power models, gliders and helicopters with extensive functions.
• Plenty of freely programmable mixers are available with up to 5-point curves for setting up very complex mixer functions.
• Integrated Trainer system with individual function switching. Freely configurable pupil/trainer channel assignment.
• Using the SD-card the system software can be updated by the user themselves to the latest version at any time.
• 20 internally stored models, can be extended without limit by SD-cards with 3,862 models per 2 GB.

General functions

• 4 Joystick functions, 8 switches, 4 rotary knobs
• 2 Operational hours counters, of which one is available per saved model
• 2 freely settable stopwatches, with memory function
• Switchable large-scale display of stopwatches
• Key-lock function
• Model selection, 20 internally saved models, extensialb by up to 3,862 models via an optional SD-card (2 GB)
• Access saved models directly from start-up screen
• Trim values display in steps or as %, with zeroising via trim memory.

System function

• Trainer mode with individual function switching and mixed operation
• Trainer function also for virtual channels, 8 or 12 channel operation
• Freely configurable pupil/trainer assignment of channels
• Hardware reversal for all controls and switches
• Joystick mode settings 1-4
• User name of 10 characters
• Choice of language from: German, English, French, Italian, Spanish, Czech, Russian or Dutch.

Basic Functions

• Graphical servo monitor with neutral- and servo- test
• Choice of model and copy function, model name of 10 characters
• Model type selection, power model, glider, helicopter
• Frequency switching General/France and modulation switching 7/12 channel.
• Freely adjustable broadcast sequence for channels 1-8
• Free choice of control types and trimmer options for all functions
• Free choice of control type and trimmer options also for virtual channels.
• For all control types (including switches etc.) free choice of trimmer options
• Digital joystick trimming, optionally with normal- or ATL (asymmetric) trim function. Optionally in "global" mode (applies to all flight modes) or in "single" mode (only applies to relevant flight mode).
• Unrestricted transmitter assignment for switched channels 9 + 10
• Servo centre offset for channels 1 - 8
• Servo reverse for channels 1 - 10
• Failsafe setting, channel 3 (throttle) in seven-channel mode, for all channels in Multi-mode.
• Servo path setting with limit function (ATV) for the 8 prop channels
• End point setting with limiter function for channels 1-8
• Switch off motor function
• Idling 2
• Trim step setting

Power model functions
A wide range of mixer menus for models with up to 4 wing-mounted servos.

• Servo path setting with limit function (ATV) for the 8 prop channels
• End point setting with limiter function for channels 1-8
• Switch off Motor function
• Idling 2
• Trim step setting
   

Functions for power models
a wide range of mixer menus for models with up to 4 wing-mounted servos. In addition to the choice of wing type, the user can also select from the following tail variants: normal, separate elevators with aileron function (ailvator) and V-tail. Deltas and powered flying wings with 2 ... 4 wing-mounted servos are also available. Once called up, these mixer menus are presented as pre-programmed items suitable for the selected model, with all the requisite mixer functions available.

• 5 Freely assignable and switchable dual-rate/expo settings. .
• 5 Available programmable mixers, linear or 5 point curve, per stored model, optionally with/without trimming and offset add-in.
• 5-Point throttle curve
• Speed setting for throttle servo
• Aileron differentiation
• Mixer spoiler (Flaperon)
• Mixer elevator -spoiler (flaperon)
• mixer rudder-aileron
• Mixer rudder-elevator
• Mixer snap roll
• Mix adjustments
• Gyro settings
• Mixer motor, for 2-step switching of motors, with individual speed setting for steps 1 /2 as well fowards and backwards.

Glider functions
Many mixer menus are also available for model gliders with up to 6 wing-mounted servos available. Optionally with or without motor. In addition to the choice of wing type, the user can also select from the following tail variants: normal, separate elevators with aileron function (ailvator) and V-tail. Flying wings with 2...6 wing-mounted servos can also be selected. These mixer menus are pre-programmed to suit the model type, and contain all the essential mixer functions as standard.

• 5 flight modes per model memory, with priority allocation and adjustable switching delays. With logical switch function.
• 5 available programmable mixers, linear or 5 point curve, per stored model, optionally with/without trimming and offset add-in.
• Aileron differentiaion
• Path setting plain flaps
• Mixer aileron-plain flaps
• Mixer aileron-rudder
• Mixer spoiler-plain flaps
• Mixer elevator-spoiler
• Mixer plain flaps-elevator
• Mixer rudder-aileron
• Mixer Butterfly, optionally with offset and delay setting
• Mixer Butterfly - elevator
• Mixer trim-mix for aileron, rudder and elevator, with speed setting and FZS-switching delay.
• Gyro setting
• Mixer motor, for 2-step switching of motors, with individual speed setting for steps 1 /2 as well as forward and back.

Helicopter functions
The mixer menus for helicopters vary mainly in the use of swashplate controls. All the classic linkage types are included as standard: H1, H2, HR3, HN3, H4 and the new H3 90° and H3 140° A special feature is the new form of variable pushrod travel compensation for the H3 and H4 types. This function eliminates a common problem found with unequal travels, which can result in servo damage can occur in the long term, when travels are fairly large or asymmetrical. The speed of the pitch-axis (elevator) function can also be adjusted, in order to avoid the run-time differences with the HR3 / HN3 120° swashplate linkage.

• 5 free programmatic linear or 5 point curve per stored model, optionally with / without trimming and offset add-in.
• Swashplate mixer
• Mixer swashplate ring
• 5-point pitch curve normal, throttle pre-selections 1,2,3, auto-rotation. With logical switch function.
• 5-point throttle curve normal, throttle preselection 1,2,3, auto-rotation. With logical switch function.
• Auto-rotation
• Swash plate mixer (virtual rotation)
• Swash plate mixer - throttle (Linear / Centre)
• Tail mixer - throttle (Linear / Center)
• 5-Point mixer tail pitch, normal, throttle preselections 1,2,3, auto-rotation. With logical switch function.
• Mixed adjustments
• Gyro mixer with 3 steps and fine trim setting
• Governor with 3 steps and fine trim setting

Specification:

Dimensions: 175 x 175 x 55 mm

Weight: 820 g

Frequency band: 2400.00

Channel spacing: 2048 kHz

Current drain: ca. 220 mA

Power Supply: 7,2 Volt NiMH-Akku

Functions: 20/10 Servos

Kit contents:

1x T8FG 2.4 GHz FASST transmitter 1x R6008HS 2.4 GHz FASST receiver 1x transmitter battery 7.2 V NiMH 1700 mAh 1x plug-in recharger Tx-Rx 170 / 150 mA 1x power switch cable 1x screwdriver